JET 708636CK DC-1100CK Dust Collector with Micron Canister
You looking to find the "
JET 708636CK DC-1100CK Dust Collector with Micron Canister" Good news! You can purchase
JET 708636CK DC-1100CK Dust Collector with Micron Canister with secure price and compare to view update price on this product. And deals on this product is available only for limited time.
Price: $849.00
Product Feature
- Industrial-quality construction effectively handles collection of wood chips and sawdust
- Quick-install collection bag makes emptying and re-attaching a snap
- Single-stage design for economical and quiet operation
- Industrial controls designed for years of trouble-free use
- Quick-connect collection bags with elastic band for fast, easy installation and removal
Product Description
The JET Model 1100 dust collector is built with industrial-quality construction, effectively handling collection of wood chips and sawdust. Comes equipped with a quick-install collection bag, single-stage design, 4 casters for portability, and permanently lubricated, fully enclosed, fan-cooled motors. Optional canister filter offers superior dust collection by capturing particles as low as 2 microns. Volts: 115V (prewired 115V), HP: 1 1/2, Hose Diameter (in.): 4 and 6, CFM: 1,100 Air Flow at 4
JET 708636CK DC-1100CK Dust Collector with Micron Canister Review
After reading a bunch of reviews, I knew Jet was the way to go. Then, with the help of a book called Dust Collection Basics, I figured out what CFM, FPM and static pressure I would need for my table saw, miter saw, jointer, bandsaw and downdraft table. The answer was on the border between the DC-600 and DC-1100. I was more concerned about the noise than additional price, but was VERY pleased to find out that this machine is MUCH quieter than I anticipated. Of course, I'm used to an over-worked shop-vac (bad bearings) so though it's not exactly silent, it is a great improvement.
I built a Thein cyclone (Google it for plans, easy to build and works GREAT!) to place on a 30 gallon galvanized trash can, and to save space, I inverted the blower motor and hung it on the wall right over the cyclone can. Now, within the same footprint, I have a 2 cycle DC setup that's safer and easier to empty, and cost me about $25 more! Then I set up each machine with JDS blast gates - I know me... if the switch is across the shop, I'll skip it for "just one cut..." then wind up with a face full of dust because most cuts are just one!
I rationalized upgrading to the 1 micron filter by considering the health problems related to dust inhalation. They go WAY beyond black kleenex and "lung cookies." I figured a couple hundred bucks now, or thousands in hospital bills and medications later. You can decide for yourself. ;o)
I will say that I was surprised to find out that, when paired with Rockler's Dust Right master system (giant 4" vacuum wand) it won't pick up screws or even zip-tie cutoffs, but it picks up every speck of dust within 12" of it! If I use a reducer, it'll pick up just about anything with the increase in velocity.
If you're reading this, you've alread made the first good decision - get a dust collector. I can't say whether it's the best around, but I'm impressed enough so far to actually sit down and write a review.
By the way, if you can't afford a full-fledged system, check out Rockler's cyclone for a 5 gal. pail and combine it with your shop-vac after replacing the filter and using a drywall/fine dust bag. The big chunks go into the cyclone, and the bag only gets filled with the finest of particles so you'll have infrequent changes. BUT - you won't get the volume of air of a DC, so your saws will still spit some dust up.
Most of the consumer Reviews tell that the "JET 708636CK DC-1100CK Dust Collector with Micron Canister" are high quality item. You can read each testimony from consumers to find out cons and pros from
JET 708636CK DC-1100CK Dust Collector with Micron Canister ...